Selected ATcT [1, 2] enthalpy of formation based on version 1.140 of the Thermochemical Network [3]

This version of ATcT results[3] was generated by additional expansion of version 1.130 to fully include the highest-level electronic structure computations described in reference [4].

Silylsilylene

Formula: SiH3SiH (g)
CAS RN: 50420-90-1
ATcT ID: 50420-90-1*0
SMILES: [SiH3][SiH]
InChI: InChI=1S/H4Si2/c1-2/h1H,2H3
InChIKey: BAGSMSWGHZVCIQ-UHFFFAOYSA-N
Hills Formula: H4Si2

2D Image:

[SiH3][SiH]
Aliases: SiH3SiH; Silylsilylene; Disilanylidene; SiHSiH3
Relative Molecular Mass: 60.20276 ± 0.00066

   ΔfH°(0 K)   ΔfH°(298.15 K)UncertaintyUnits
317.1309.3± 2.0kJ/mol

3D Image of SiH3SiH (g)

spin ON           spin OFF
          

Top contributors to the provenance of ΔfH° of SiH3SiH (g)

The 20 contributors listed below account only for 43.6% of the provenance of ΔfH° of SiH3SiH (g).
A total of 95 contributors would be needed to account for 90% of the provenance.

Please note: The list is limited to 20 most important contributors or, if less, a number sufficient to account for 90% of the provenance. The Reference acts as a further link to the relevant references and notes for the measurement. The Measured Quantity is normaly given in the original units; in cases where we have reinterpreted the original measurement, the listed value may differ from that given by the authors. The quoted uncertainty is the a priori uncertainty used as input when constructing the initial Thermochemical Network, and corresponds either to the value proposed by the original authors or to our estimate; if an additional multiplier is given in parentheses immediately after the prior uncertainty, it corresponds to the factor by which the prior uncertainty needed to be multiplied during the ATcT analysis in order to make that particular measurement consistent with the prevailing knowledge contained in the Thermochemical Network.

Contribution
(%)
TN
ID
Reaction Measured Quantity Reference
4.08199.1 SiH3SiH3 (g) → 2 Si (cr,l) + 3 H2 (g) ΔrH°(298.15 K) = -19.1 ± 0.6 (×1.576) kcal/molGunn 1961, est unc
3.58157.1 Si (cr,l) + 2 F2 (g) → SiF4 (g) ΔrH°(298.15 K) = -385.98 ± 0.19 kcal/molWise 1963, Wise 1963, Wise 1962
3.38163.1 SiH4 (g) → Si (cr,l) + 2 H2 (g) ΔrH°(298.15 K) = -8.3 ± 0.5 kcal/molGunn 1961, Gurvich TPIS, est unc
2.98238.4 SiH3SiH (g, singlet) → [SiH3SiH]+ (g) ΔrH°(0 K) = 8.352 ± 0.040 eVRuscic W1RO
2.68100.2 Si (cr,l) → Si (g) ΔrG°(1525 K) = 231.1 ± 2.0 kJ/molBatdorf 1959, 3rd Law
2.38244.6 SiH3SiH (g, singlet) → SiH2SiH2 (g, singlet) ΔrH°(0 K) = -6.88 ± 0.70 kcal/molDolgonos 2008, est unc
2.18232.4 SiH2SiH2 (g, singlet) H2 (g) → SiH3SiH3 (g) ΔrH°(0 K) = -47.68 ± 1.2 kcal/molRuscic W1RO
1.98135.6 SiO2 (cr,l) Si (cr,l) → 2 SiO (g) ΔrG°(1618 K) = 37.94 ± 0.29 kcal/molRamstad 1961, 3rd Law, Gurvich TPIS
1.98154.8 SiF4 (g) → Si (g) + 4 F (g) ΔrH°(0 K) = 565.92 ± 0.30 kcal/molKarton 2011
1.98233.4 SiH2SiH2 (g, singlet) SiH4 (g) → SiH3SiH3 (g) SiH2 (g, singlet) ΔrH°(0 K) = 7.48 ± 1.2 kcal/molRuscic W1RO
1.98249.5 SiH3SiH3 (g) → [SiH3SiH]+ (g) H2 (g) ΔrH°(0 K) = 10.706 ± 0.040 eVRuscic W1RO
1.88232.2 SiH2SiH2 (g, singlet) H2 (g) → SiH3SiH3 (g) ΔrH°(0 K) = -45.74 ± 1.3 kcal/molRuscic G4
1.88247.4 SiH3SiH (g, singlet) + 2 SiH2 (g, singlet) → SiH2SiH2 (g, singlet) SiH3 (g) SiH (g) ΔrH°(0 K) = 1.09 ± 0.90 kcal/molRuscic W1RO
1.68127.5 SiO (g) → Si (g) O (g) ΔrH°(0 K) = 189.99 ± 0.30 kcal/molFeller 2008
1.68127.10 SiO (g) → Si (g) O (g) ΔrH°(0 K) = 190.23 ± 0.30 kcal/molKarton 2011
1.68233.2 SiH2SiH2 (g, singlet) SiH4 (g) → SiH3SiH3 (g) SiH2 (g, singlet) ΔrH°(0 K) = 7.87 ± 1.3 kcal/molRuscic G4
1.58232.1 SiH2SiH2 (g, singlet) H2 (g) → SiH3SiH3 (g) ΔrH°(0 K) = -45.65 ± 1.4 kcal/molRuscic G3X
1.5546.1 SiF4 (g) + 2 H2O (cr,l) → Si (cr,l) O2 (g) + 4 HF (aq, 5 H2O) ΔrH°(298.15 K) = 899.77 ± 1.20 kJ/molPaulechka 2020, Vorobev 1960, Hummel 1959, Johnson 1987, Good 1964, Good 1964, Johnson 1973
1.48235.5 SiH3SiH3 (g) → [SiH2SiH2]+ (g) H2 (g) ΔrH°(0 K) = 10.128 ± 0.040 eVRuscic W1RO
1.48247.2 SiH3SiH (g, singlet) + 2 SiH2 (g, singlet) → SiH2SiH2 (g, singlet) SiH3 (g) SiH (g) ΔrH°(0 K) = 1.60 ± 1.00 kcal/molRuscic G4

Top 10 species with enthalpies of formation correlated to the ΔfH° of SiH3SiH (g)

Please note: The correlation coefficients are obtained by renormalizing the off-diagonal elements of the covariance matrix by the corresponding variances.
The correlation coefficient is a number from -1 to 1, with 1 representing perfectly correlated species, -1 representing perfectly anti-correlated species, and 0 representing perfectly uncorrelated species.


Correlation
Coefficent
(%)
Species Name Formula Image    ΔfH°(0 K)    ΔfH°(298.15 K) Uncertainty Units Relative
Molecular
Mass
ATcT ID
100.0 SilylsilyleneSiH3SiH (g, singlet)[SiH3][SiH]317.1309.3± 2.0kJ/mol60.20276 ±
0.00066
50420-90-1*2
84.9 DisileneSiH2SiH2 (g, singlet)[SiH2]=[SiH2]288.6280.0± 1.9kJ/mol60.20276 ±
0.00066
15435-77-5*2
84.9 DisileneSiH2SiH2 (g)[SiH2]=[SiH2]288.6280.0± 1.9kJ/mol60.20276 ±
0.00066
15435-77-5*0
82.2 mu-HydrotrihydrodisiliconSiH2(HSiH) (g)[SiH2]([H-]1)[SiH+]1317.7307.6± 2.2kJ/mol60.20276 ±
0.00066
497967-56-3*0
67.8 DisileneSiH2SiH2 (g, triplet)[SiH2]=[SiH2]393.3384.8± 2.3kJ/mol60.20276 ±
0.00066
15435-77-5*1
64.4 SilylsilyleneSiH3SiH (g, triplet)[SiH3][SiH]381.2372.4± 2.7kJ/mol60.20276 ±
0.00066
50420-90-1*1
63.6 Disilene cation[SiH2SiH2]+ (g)[SiH2]=[SiH2+]1069.41060.4± 2.0kJ/mol60.20221 ±
0.00066
108492-63-3*0
61.6 DisilaneSiH3SiH3 (g)[SiH3][SiH3]92.176.0± 1.3kJ/mol62.21864 ±
0.00073
1590-87-0*0
60.7 DisilanylSiH3SiH2 (g)[SiH3][SiH2]242.6230.6± 1.6kJ/mol61.21070 ±
0.00069
73151-72-1*0
60.3 1-Disilanylium-1-yl[SiH3SiH]+ (g)[SiH3][SiH+]1124.01116.4± 2.3kJ/mol60.20221 ±
0.00066
108492-64-4*0

Most Influential reactions involving SiH3SiH (g)

Please note: The list, which is based on a hat (projection) matrix analysis, is limited to no more than 20 largest influences.

Influence
Coefficient
TN
ID
Reaction Measured Quantity Reference
1.0008242.1 SiH3SiH (g) → SiH3SiH (g, singlet) ΔrH°(0 K) = 0 ± 0 cm-1Ruscic W1RO, Ruscic G4, Ruscic CBS-n, Ruscic G3X


References
1   B. Ruscic, R. E. Pinzon, M. L. Morton, G. von Laszewski, S. Bittner, S. G. Nijsure, K. A. Amin, M. Minkoff, and A. F. Wagner,
Introduction to Active Thermochemical Tables: Several "Key" Enthalpies of Formation Revisited.
J. Phys. Chem. A 108, 9979-9997 (2004) [DOI: 10.1021/jp047912y]
2   B. Ruscic, R. E. Pinzon, G. von Laszewski, D. Kodeboyina, A. Burcat, D. Leahy, D. Montoya, and A. F. Wagner,
Active Thermochemical Tables: Thermochemistry for the 21st Century.
J. Phys. Conf. Ser. 16, 561-570 (2005) [DOI: 10.1088/1742-6596/16/1/078]
3   B. Ruscic and D. H. Bross,
Active Thermochemical Tables (ATcT) values based on ver. 1.140 of the Thermochemical Network (2024); available at ATcT.anl.gov
4   J. H. Thorpe, J. L. Kilburn, D. Feller, P. B. Changala, D. H. Bross, B. Ruscic, and J. F. Stanton,
Elaborated Thermochemical Treatment of HF, CO, N2, and H2O: Insight into HEAT and Its Extensions
J. Chem. Phys. 155, 184109 (2021) [DOI: 10.1063/5.0069322]
5   B. Ruscic,
Uncertainty Quantification in Thermochemistry, Benchmarking Electronic Structure Computations, and Active Thermochemical Tables.
Int. J. Quantum Chem. 114, 1097-1101 (2014) [DOI: 10.1002/qua.24605]
6   B. Ruscic and D. H. Bross,
Thermochemistry
Computer Aided Chem. Eng. 45, 3-114 (2019) [DOI: 10.1016/B978-0-444-64087-1.00001-2]

Formula
The aggregate state is given in parentheses following the formula, such as: g - gas-phase, cr - crystal, l - liquid, etc.

Uncertainties
The listed uncertainties correspond to estimated 95% confidence limits, as customary in thermochemistry (see, for example, Ruscic [5] and Ruscic and Bross[6]).
Note that an uncertainty of ± 0.000 kJ/mol indicates that the estimated uncertainty is < ± 0.0005 kJ/mol.

Website Functionality Credits
The reorganization of the website was developed and implemented by David H. Bross (ANL).
The find function is based on the complete Species Dictionary entries for the appropriate version of the ATcT TN.
The molecule images are rendered by Indigo-depict.
The XYZ renderings are based on Jmol: an open-source Java viewer for chemical structures in 3D. http://www.jmol.org/.

Acknowledgement
This work was supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences and Biosciences under Contract No. DE-AC02-06CH11357.